Merge branch 'net-next-2024-03-30--06-00' into HEAD

Author: Your Name

Documentation/conf.py

@@ -75,6 +75,8 @@ def have_command(cmd):
             "__rcu",
             "__user",
             "__force",
+            "__counted_by_le",
+            "__counted_by_be",
 
             # include/linux/compiler_attributes.h:
             "__alias",

Documentation/devicetree/bindings/net/airoha,en8811h.yaml

@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/airoha,en8811h.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha EN8811H PHY
+
+maintainers:
+  - Eric Woudstra <[email protected]>
+
+description:
+  The Airoha EN8811H PHY has the ability to reverse polarity
+  on the lines to and/or from the MAC. It is reversed by
+  the booleans in the devicetree node of the phy.
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+properties:
+  compatible:
+    enum:
+      - ethernet-phy-id03a2.a411
+
+  reg:
+    maxItems: 1
+
+  airoha,pnswap-rx:
+    type: boolean
+    description:
+      Reverse rx polarity of the SERDES. This is the receiving
+      side of the lines from the MAC towards the EN881H.
+
+  airoha,pnswap-tx:
+    type: boolean
+    description:
+      Reverse tx polarity of SERDES. This is the transmitting
+      side of the lines from EN8811H towards the MAC.
+
+required:
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-phy@1 {
+            compatible = "ethernet-phy-id03a2.a411";
+            reg = <1>;
+            airoha,pnswap-rx;
+        };
+    };

Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml

@@ -94,6 +94,10 @@ properties:
 
   local-bd-address: true
 
+  qcom,local-bd-address-broken:
+    type: boolean
+    description:
+      boot firmware is incorrectly passing the address in big-endian order
 
 required:
   - compatible

Documentation/devicetree/bindings/net/stm32-dwmac.yaml

@@ -82,6 +82,13 @@ properties:
       Should be phandle/offset pair. The phandle to the syscon node which
       encompases the glue register, and the offset of the control register
 
+  st,ext-phyclk:
+    description:
+      set this property in RMII mode when you have PHY without crystal 50MHz and want to
+      select RCC clock instead of ETH_REF_CLK. OR in RGMII mode when you want to select
+      RCC clock instead of ETH_CLK125.
+    type: boolean
+
   st,eth-clk-sel:
     description:
       set this property in RGMII PHY when you want to select RCC clock instead of ETH_CLK125.

Documentation/mm/page_frags.rst

@@ -25,7 +25,7 @@ to be disabled when executing the fragment allocation.
 The network stack uses two separate caches per CPU to handle fragment
 allocation.  The netdev_alloc_cache is used by callers making use of the
 netdev_alloc_frag and __netdev_alloc_skb calls.  The napi_alloc_cache is
-used by callers of the __napi_alloc_frag and __napi_alloc_skb calls.  The
+used by callers of the __napi_alloc_frag and napi_alloc_skb calls.  The
 main difference between these two calls is the context in which they may be
 called.  The "netdev" prefixed functions are usable in any context as these
 functions will disable interrupts, while the "napi" prefixed functions are

Documentation/netlink/specs/tc.yaml

@@ -1099,6 +1099,19 @@ definitions:
       -
         name: offmask
         type: s32
+  -
+    name: tc-u32-mark
+    type: struct
+    members:
+      -
+        name: val
+        type: u32
+      -
+        name: mask
+        type: u32
+      -
+        name: success
+        type: u32
   -
     name: tc-u32-sel
     type: struct
@@ -1774,6 +1787,44 @@ attribute-sets:
       -
         name: key-ex
         type: binary
+  -
+    name: tc-act-police-attrs
+    attributes:
+      -
+        name: tbf
+        type: binary
+        struct: tc-police
+      -
+        name: rate
+        type: binary # TODO
+      -
+        name: peakrate
+        type: binary # TODO
+      -
+        name: avrate
+        type: u32
+      -
+        name: result
+        type: u32
+      -
+        name: tm
+        type: binary
+        struct: tcf-t
+      -
+        name: pad
+        type: pad
+      -
+        name: rate64
+        type: u64
+      -
+        name: peakrate64
+        type: u64
+      -
+        name: pktrate64
+        type: u64
+      -
+        name: pktburst64
+        type: u64
   -
     name: tc-act-simple-attrs
     attributes:

Documentation/networking/devlink/devlink-eswitch-attr.rst

@@ -0,0 +1,76 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==========================
+Devlink E-Switch Attribute
+==========================
+
+Devlink E-Switch supports two modes of operation: legacy and switchdev.
+Legacy mode operates based on traditional MAC/VLAN steering rules. Switching
+decisions are made based on MAC addresses, VLANs, etc. There is limited ability
+to offload switching rules to hardware.
+
+On the other hand, switchdev mode allows for more advanced offloading
+capabilities of the E-Switch to hardware. In switchdev mode, more switching
+rules and logic can be offloaded to the hardware switch ASIC. It enables
+representor netdevices that represent the slow path of virtual functions (VFs)
+or scalable-functions (SFs) of the device. See more information about
+:ref:`Documentation/networking/switchdev.rst <switchdev>` and
+:ref:`Documentation/networking/representors.rst <representors>`.
+
+In addition, the devlink E-Switch also comes with other attributes listed
+in the following section.
+
+Attributes Description
+======================
+
+The following is a list of E-Switch attributes.
+
+.. list-table:: E-Switch attributes
+   :widths: 8 5 45
+
+   * - Name
+     - Type
+     - Description
+   * - ``mode``
+     - enum
+     - The mode of the device. The mode can be one of the following:
+
+       * ``legacy`` operates based on traditional MAC/VLAN steering
+         rules.
+       * ``switchdev`` allows for more advanced offloading capabilities of
+         the E-Switch to hardware.
+   * - ``inline-mode``
+     - enum
+     - Some HWs need the VF driver to put part of the packet
+       headers on the TX descriptor so the e-switch can do proper
+       matching and steering. Support for both switchdev mode and legacy mode.
+
+       * ``none`` none.
+       * ``link`` L2 mode.
+       * ``network`` L3 mode.
+       * ``transport`` L4 mode.
+   * - ``encap-mode``
+     - enum
+     - The encapsulation mode of the device. Support for both switchdev mode
+       and legacy mode. The mode can be one of the following:
+
+       * ``none`` Disable encapsulation support.
+       * ``basic`` Enable encapsulation support.
+
+Example Usage
+=============
+
+.. code:: shell
+
+    # enable switchdev mode
+    $ devlink dev eswitch set pci/0000:08:00.0 mode switchdev
+
+    # set inline-mode and encap-mode
+    $ devlink dev eswitch set pci/0000:08:00.0 inline-mode none encap-mode basic
+
+    # display devlink device eswitch attributes
+    $ devlink dev eswitch show pci/0000:08:00.0
+      pci/0000:08:00.0: mode switchdev inline-mode none encap-mode basic
+
+    # enable encap-mode with legacy mode
+    $ devlink dev eswitch set pci/0000:08:00.0 mode legacy inline-mode none encap-mode basic

Documentation/networking/devlink/index.rst

@@ -67,6 +67,7 @@ general.
    devlink-selftests
    devlink-trap
    devlink-linecard
+   devlink-eswitch-attr
 
 Driver-specific documentation
 -----------------------------

Documentation/networking/representors.rst

@@ -1,4 +1,5 @@
 .. SPDX-License-Identifier: GPL-2.0
+.. _representors:
 
 =============================
 Network Function Representors

Documentation/translations/zh_CN/mm/page_frags.rst

@@ -25,7 +25,7 @@ sk_buff->head使用，或者用于skb_shared_info的 “frags” 部分。
 
 网络堆栈在每个CPU使用两个独立的缓存来处理碎片分配。netdev_alloc_cache被使用
 netdev_alloc_frag和__netdev_alloc_skb调用的调用者使用。napi_alloc_cache
-被调用__napi_alloc_frag和__napi_alloc_skb的调用者使用。这两个调用的主要区别是
+被调用__napi_alloc_frag和napi_alloc_skb的调用者使用。这两个调用的主要区别是
 它们可能被调用的环境。“netdev” 前缀的函数可以在任何上下文中使用，因为这些函数
 将禁用中断，而 ”napi“ 前缀的函数只可以在softirq上下文中使用。