Ikoka Nano Variant

variants/ikoka_nano_nrf/IkokaNanoNRFBoard.cpp

@@ -0,0 +1,94 @@
+#ifdef XIAO_NRF52
+
+#include <Arduino.h>
+#include "IkokaNanoNRFBoard.h"
+
+#include <bluefruit.h>
+#include <Wire.h>
+
+static BLEDfu bledfu;
+
+static void connect_callback(uint16_t conn_handle) {
+  (void)conn_handle;
+  MESH_DEBUG_PRINTLN("BLE client connected");
+}
+
+static void disconnect_callback(uint16_t conn_handle, uint8_t reason) {
+  (void)conn_handle;
+  (void)reason;
+
+  MESH_DEBUG_PRINTLN("BLE client disconnected");
+}
+
+void IkokaNanoNRFBoard::begin() {
+  // for future use, sub-classes SHOULD call this from their begin()
+  startup_reason = BD_STARTUP_NORMAL;
+
+  pinMode(PIN_VBAT, INPUT);
+  pinMode(VBAT_ENABLE, OUTPUT);
+  digitalWrite(VBAT_ENABLE, HIGH);
+
+#ifdef PIN_USER_BTN
+  pinMode(PIN_USER_BTN, INPUT_PULLUP);
+#endif
+
+#if defined(PIN_WIRE_SDA) && defined(PIN_WIRE_SCL)
+  Wire.setPins(PIN_WIRE_SDA, PIN_WIRE_SCL);
+#endif
+
+  Wire.begin();
+
+#ifdef P_LORA_TX_LED
+  pinMode(P_LORA_TX_LED, OUTPUT);
+  digitalWrite(P_LORA_TX_LED, HIGH);
+#endif
+
+//  pinMode(SX126X_POWER_EN, OUTPUT);
+//  digitalWrite(SX126X_POWER_EN, HIGH);
+  delay(10);   // give sx1262 some time to power up
+}
+
+bool IkokaNanoNRFBoard::startOTAUpdate(const char *id, char reply[]) {
+  // Config the peripheral connection with maximum bandwidth
+  // more SRAM required by SoftDevice
+  // Note: All config***() function must be called before begin()
+  Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
+  Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);
+
+  Bluefruit.begin(1, 0);
+  // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
+  Bluefruit.setTxPower(4);
+  // Set the BLE device name
+  Bluefruit.setName("XIAO_NRF52_OTA");
+
+  Bluefruit.Periph.setConnectCallback(connect_callback);
+  Bluefruit.Periph.setDisconnectCallback(disconnect_callback);
+
+  // To be consistent OTA DFU should be added first if it exists
+  bledfu.begin();
+
+  // Set up and start advertising
+  // Advertising packet
+  Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
+  Bluefruit.Advertising.addTxPower();
+  Bluefruit.Advertising.addName();
+
+  /* Start Advertising
+    - Enable auto advertising if disconnected
+    - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
+    - Timeout for fast mode is 30 seconds
+    - Start(timeout) with timeout = 0 will advertise forever (until connected)
+
+    For recommended advertising interval
+    https://developer.apple.com/library/content/qa/qa1931/_index.html
+  */
+  Bluefruit.Advertising.restartOnDisconnect(true);
+  Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
+  Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
+  Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds
+
+  strcpy(reply, "OK - started");
+  return true;
+}
+
+#endif

variants/ikoka_nano_nrf/IkokaNanoNRFBoard.h

@@ -0,0 +1,60 @@
+#pragma once
+
+#include <MeshCore.h>
+#include <Arduino.h>
+
+#ifdef XIAO_NRF52
+
+class IkokaNanoNRFBoard : public mesh::MainBoard {
+protected:
+  uint8_t startup_reason;
+
+public:
+  void begin();
+  uint8_t getStartupReason() const override { return startup_reason; }
+
+#if defined(P_LORA_TX_LED)
+  void onBeforeTransmit() override {
+    digitalWrite(P_LORA_TX_LED, LOW);   // turn TX LED on
+    #if defined(LED_BLUE)
+       // turn off that annoying blue LED before transmitting
+       digitalWrite(LED_BLUE, HIGH);
+    #endif
+  }
+  void onAfterTransmit() override {
+    digitalWrite(P_LORA_TX_LED, HIGH);   // turn TX LED off
+    #if defined(LED_BLUE)
+       // do it after transmitting too, just in case
+       digitalWrite(LED_BLUE, HIGH);
+    #endif
+  }
+#endif
+
+  uint16_t getBattMilliVolts() override {
+    // Please read befor going further ;)
+    // https://wiki.seeedstudio.com/XIAO_BLE#q3-what-are-the-considerations-when-using-xiao-nrf52840-sense-for-battery-charging
+
+    // We can't drive VBAT_ENABLE to HIGH as long 
+    // as we don't know wether we are charging or not ...
+    // this is a 3mA loss (4/1500)
+    digitalWrite(VBAT_ENABLE, LOW);
+    int adcvalue = 0;
+    analogReadResolution(12);
+    analogReference(AR_INTERNAL_3_0);  
+    delay(10);
+    adcvalue = analogRead(PIN_VBAT);
+    return (adcvalue * ADC_MULTIPLIER * AREF_VOLTAGE) / 4.096;
+  }
+
+  const char *getManufacturerName() const override {
+    return MANUFACTURER_STRING;
+  }
+
+  void reboot() override {
+    NVIC_SystemReset();
+  }
+
+  bool startOTAUpdate(const char *id, char reply[]) override;
+};
+
+#endif